Fortigate wifi ssid


  • Wireless network examples
  • Configuring a FortiWifi as a Wifi Client/Router
  • The 7 surefire tips for setting up your FortiAP
  • Corporate Network on the Go: Fortinet Remote AP
  • Fortigate: AP-Bridge with a hardware switch
  • Wireless network examples

    So start off by logging in to the Fortigate. New, to proceed we need to delete some associated interfaces. In here we need to remove some Software Switch interface memberships and delete Wifi interfaces. Click the wgt. Click the Internal Software Switch, and then Edit. Click the X on the Wifi member to remove from the list. The Select Entries list will appear. Dismiss this with the Close button, then Click OK. Give it 30 seconds — 1 minute and connectivity should be re-established. You may need to refresh the page, but once connectivity has been restored, note that the Wifi interface no longer in the Internal Software Switch Interface Members.

    Click OK to return to the Interfaces page. Click this, then click Delete, then click OK to confirm the deletion. Click on the button, then click Apply.

    Once it has finished rebooting, log back in. Click on this option. A Wifi Connection Setting prompt will appear to select the Security Mode you wish to authenticate with. You may wish to edit the interface settings to assign a static IP address to make it easier to configured routing for other parts of your network can reach the wired LAN on the FortiGate.

    To change to a static IP address, click the Manual button and enter the IP address you wish to use that is part of your wireless network subnet. In this instance I used Click OK to apply the new IP address. Assuming the routes you require are not present, click the Create New button. Finally, click OK to save the static route.

    For my tests, I turned off my wifi to be sure, connected to a port on the FortiGate, and browsed to my website.

    Configuring a FortiWifi as a Wifi Client/Router

    WPA2-Enterprise with Every end user, including the authentication server, that participates in EAP-TLS must possess at least two certificates: 1 a client certificate signed by the certificate authority CA and 2 a copy of the CA root certificate.

    This recipe specifically focus on the configuration of the FortiAuthenticator, FortiGate and Windows 7 computer. Creating a local CA on FortiAuthenticator The FortiAuthenticator will act as the certificate authority for all certificates authenticated for client access. To enable this functionality, a self-signed root CA certificate must be generated. Click Create New. Complete the information in the fields pertaining to your organization. Enter the Secret password. On Authentication method select Password-only authentication and on Username input format select username realm.

    Configuring local user on FortiAuthenticator The authentication of the WiFi client will be tied to a user account on the FortiAuthenticator. In this scenario, a local user will be configured but remote users associated with LDAP can be configured as well.

    Fill out applicable user information. Configuring local user certificate on FortiAuthenticator The certificate created locally on the FortiAuthenticator will be associated with the local user. It is important to note that the Name CN must match the username exactly of the user that is registered in the FortiAuthenticator i.

    Fill out applicable user information to map the certificate to the correct user. Select Create New. Type FortiAuth. Optionally, you can click Test Connectivity.

    Click the checkbox beside the certificate. This password will be used when importing the certificate into a Windows 7 computer. Click OK. Click Finish. Importing user certificate into Windows 7 On the Windows 7 computer, double-click the downloaded certificate file from the FortiAuthenticator. This will launch the Welcome to Certificate Import Wizard.

    Click Next. Make sure the correct certificate is shown in the File Name section in the File to Import window. Below Password, type the password created on the FortiAuthenticator during the export of the certificate. Select Mark this key as exportable. Leave remaining defaults. In the Certificate Store, choose the Place all certificates in the following store. Click Browse and choose Personal. Click Next, and then Finish.

    A dialog box will show up confirming the certificate was imported successfully. Then click on Settings. On Smart Card or other Certificates Properties. Under When connecting, select Use a certificate on this computer, and check Use simple certificate selection.

    Click OK and click OK. To enable this, you will need to import the CA from the FortiAuthenticator to the Windows 7 computer and make sure that it is enabled as a Trusted Root Certification Authority. The configuration for the Windows 7 computer has been completed and the user should be able to authenticate to WiFi via the certificate without using username and password. Results on FortiAuthenticator When the user attempts to authenticate to WiFi using the certificate, they will have a specific log entry in the FortiAuthenticator.

    The 7 surefire tips for setting up your FortiAP

    Every end user, including the authentication server, that participates in EAP-TLS must possess at least two certificates: 1 a client certificate signed by the certificate authority CA and 2 a copy of the CA root certificate.

    This recipe specifically focus on the configuration of the FortiAuthenticator, FortiGate and Windows 7 computer. Creating a local CA on FortiAuthenticator The FortiAuthenticator will act as the certificate authority for all certificates authenticated for client access. To enable this functionality, a self-signed root CA certificate must be generated.

    Corporate Network on the Go: Fortinet Remote AP

    Click Create New. Complete the information in the fields pertaining to your organization. Enter the Secret password. On Authentication method select Password-only authentication and on Username input format select username realm. Configuring local user on FortiAuthenticator The authentication of the WiFi client will be tied to a user account on the FortiAuthenticator. In this scenario, a local user will be configured but remote users associated with LDAP can be configured as well. Fill out applicable user information.

    Configuring local user certificate on FortiAuthenticator The certificate created locally on the FortiAuthenticator will be associated with the local user. It is important to note that the Name CN must match the username exactly of the user that is registered in the FortiAuthenticator i.

    Fortigate: AP-Bridge with a hardware switch

    However you can see each step of the process and ultimately when access is granted to the user to access the Internet via the guest network. I hope this has been a helpful explanation of how to configure the FortiGate to allow a wireless users to access a guest network with the FortiAuthenticator serving the guest portal.

    In the last and final installment, I will explain how to configure the FortiAuthenticator and FortiGate to work in conjunction where users who have previously authenticated will not have to do subsequent authentications after their initial registration and successful log on. As always, if you have any questions or feedback about the information included in this post, leave a comment below.

    Click on the button, then click Apply. Once it has finished rebooting, log back in. Click on this option. A Wifi Connection Setting prompt will appear to select the Security Mode you wish to authenticate with.

    You may wish to edit the interface settings to assign a static IP address to make it easier to configured routing for other parts of your network can reach the wired LAN on the FortiGate. To change to a static IP address, click the Manual button and enter the IP address you wish to use that is part of your wireless network subnet. In this instance I used


    thoughts on “Fortigate wifi ssid

    Leave a Reply

    Your email address will not be published. Required fields are marked *